Free shipping
Low Price
View Cart

    DuraVent DuraLiner 48 inch Round Rigid Reline Pipe - 6 inch Diameter - 6DLR-48

    List Price: $229.99
    Sale Price: $185.95
    You Save: $44.04 (19%)
    In Stock.
    * Usually Ships Same Business Day.
    • DuraLiner 48" Round Rigid Liner
    • 6-in. diameter
    • .016 304 alloy stainless steel construction
    • Designed to provide resistance to creosote build up in oversized masonry chimneys venting open fireplaces or appliance
    See complete product details >>
    Product Details
    Free Venting Design & Quote:
    Manufacturer: DuraVent
    Part Number: 6DLR-48
    eFireplaceStore Item Number: CPF-69273
    UPC: 662492010297


    • DuraLiner 48" Round Rigid Liner
    • 6-in. diameter
    • .016 304 alloy stainless steel construction
    • Designed to provide resistance to creosote build up in oversized masonry chimneys venting open fireplaces or appliance

    *Venting Requirements: This unit requires venting pipe with an inner diameter of 6 Inches. Please see the Venting Components section on this page for venting pipe that must be used with this unit.

    Whether you have a brand new fireplace or an older, well-used one, you may have concerns about creosote, chimney tar, build up. A duraliner, constructed with alloy stainless steel and factory insulated with a 0.5 inch blanket of protection, is resistant to creosote buildup within the chimney masonry. The forty-eight inch round pipe with a six inch diameter has durable, flexible sections that have pre-drilled holes in the ends to twist and lock flawlessly into corresponding metal parts. It comes with a 25 year manufacturer's warranty.
    Customer Questions & Answers
    3 Questions & 3 Answers
    from Marbury , MD asked:
    April 10, 2017
    I have an old chimney that will not pass inspection. The chimney runs from the basement through the first and second floors and then out of the roof of an old farm house. I have a US stove wood/coal furnace in the basement with a six inch rear pipe. The chimney has a roughly 6" terracotta liner. Will this product fit inside the liner? And will this product pass the inspection?
    1 Answer
    We do not currently offer any 6" chimney liner that will fit inside an existing 6" terracotta liner. If you plan to remove the existing 6" liner with a tile breaker, you will likely be able to use this product.
    Will M.
    on April 10, 2017

    from Weeping Water, NE asked:
    October 13, 2014
    What is the outer diameter (OD) of this 6" chimney liner?
    1 Answer
    The O.D. of this rigid liner is 6 5/8 inches.
    on October 14, 2014

    Kev Martin
    from Franklin, NC asked:
    November 4, 2011
    I am almost done breaking up the tile in my flue and looking forward to the next step. You recommended i get the Duraliner relining pipe- which sounds good but a few questions- 1. the flue collar and first few feet of flue heading out and up towards the main flue (in my basement) makes a couple of slight turns before reaching the main flue, which is then vertically all the way to the top. I'm envisioning that i could use a flexible section first, and then build on the rigid pieces afterwards until i reach the top. Will in need to do any extra insulation in the first section since it would be flexible pipe there? 2. installation- how to i get it all in place? is there something that can be attached to the first section or pipe and then lowered through the flue into the open end on the bottom at the collar so we can pull it through into place?
    1 Answer
    While it is recommended that any flexible portion of Dura-liner be insulated, it is not always necessary. In your case, if the flexible section is located in an area below the flue tiles you have been removing, it would not be needed. However, the liner would need insulation if it is going to be in a part of the chimney that previously had flue tiles. As far as the installation goes, it is most common to attach the components at the top of the chimney and feed them down gradually. Tying a rope to the first piece of liner and dropping it down the chimney is a good way to guide the assembly down into place, especially if someone can pull on the rope from the bottom to assist in getting the liner through any tight places.
    Collin C. - NFI Master Hearth Professional
    on November 7, 2011

    Customer Reviews

    Let Our Experts Design
    Your Venting System


    Find the Right Gas Logs
    For Your Fireplace

    Sign-up for our Email!
    Enter your email for new arrivals and special offers.