- FireplacesShop By TypeShop By UseShop By Brand
- Fireplace InsertsShop By TypeInsert AccessoriesShop By Brand
- Stoves
- Gas LogsShop By TypeShop Vented Log StylesShop Ventless Log Styles
Charred Aged
Split OakCharred
Frontier OakEvening
FyreEvening
Fyre SplitValley
Oak - Heaters
- Mantels
- Accessories
- Chimneys & Venting
- Outdoor Living
- Guides & Articles
FireplacesFireplace InsertsStovesGas LogsHeatersMantelsAccessoriesChimneys & VentingOutdoor LivingGuides & ArticlesMy AccountOrder StatusHelp
image {{ pictureNum }} of {{ imageArray2.length }}
× 
Ask a Fireplace Specialist:
|
Superior 8DM and 8HT Chimney Storm Collar - For 8-Inch Inner Diameter Superior Chimneys
Popular Accessories for this Item
Product Details
Part Number: SC1-1 eFireplaceStore Item Number: FSD-VSC1-20-8DM UPC: 043593040947 Features
*Venting Requirements: This unit requires venting pipe with an inner diameter of 8 Inches. Please see the Venting Components section on this page if available for venting pipe that must be used with this unit. IHP/Superior Wood Fireplace Storm Collar for 8 Inch Chimney Pipe. Only IHP/Superior Chimney Wood Fireplace Chimney Liners and Chimney Liner Accessories are approved for use with IHP/Superior Wood Fireplaces. They are UL approved and are not for use with any product other than IHP/Superior Wood Burning Fireplaces. |
Customers Who Viewed This Item Also Viewed
Customer Questions & Answers
4 Questions &
4 Answers
Joe
from Fayetteville, AR asked:
February 3, 2021
Will this fit the m83 pipe? Outer diameter of triple wall pipe 13+”
1 Answer
This storm collar is intended for use with the Superior 8DM pipe, which has a 12-3/8-inch outside diameter.
Submitted by:
Tyler M. - NFI Master Hearth Professional
on February 4, 2021
Fred M
from red bank nj asked:
December 19, 2017
will this fit Majestic SK 8" pipe
1 Answer
It would, but we do carry the correct flashing for the SK8.
Submitted by:
Owen
on December 19, 2017
Bob
from IL asked:
October 22, 2017
With the 8" diameter version, what is the OD of the finished bottom?
1 Answer
Storm collars are adjustable, so the OD is undefined. That one is made to cover a pipe with a 8" ID and a 10" OD.
Submitted by:
Owen
on October 23, 2017
Ron
from Flagstaff, AZ asked:
May 22, 2017
What gauge of material is used to construct this collar?
1 Answer
The storm collar is approximately 28 gauge.
Submitted by:
Will M.
on May 23, 2017
Customer Reviews
Review Summary
3.3
3 Reviews
5
33% (1)
4
33% (1)
3
0% (0)
2
0% (0)
1
33% (1)
67% Recommend this product (2 of 3 responses)
By John from
Laurel, TX on May 23, 2017
Far Too Large
It did not work for my application, I needed 8". The unit comes as a 20" piece that can be tightened down, however, it will not hold together at 8".
By Larry C. from
Petal MS on March 26, 2015
I would recommend this item to a friend.
what I needed
fit great
Proslooks good
By Kris from
Oklahoma on December 11, 2014
I would recommend this item to a friend.
Works well
Not much to say, it fits pipe tightly and should prevent leaks when sealed with silicone at junction of pipe and flashing. Again, a bit pricey for die stamped steel, but not bad amortized over 20 years.
